Epson Printer nozzle unblocker 60ml Printhead cleaner XP-322 XP-325

EUR 9,26 Achat immédiat, Cliquez pour voir les frais d'expédition, 30-Jour Retours, Garantie client eBay
Vendeur: theitexchange ✉️ (9.159) 99.7%, Lieu où se trouve: Stoke-on-Trent, GB, Lieu de livraison: GB, Numéro de l'objet: 291813703316 Epson Printer nozzle unblocker 60ml Printhead cleaner XP-322 XP-325.

Epson Printer nozzle unblocker 60ml Printhead cleaner XP-322 XP-325

Availability: in stock

Specially formulated for the Epson Expression range of printers

XP-225, XP-322, XP-325, XP-422, XP-425

XP-235, XP-332, XP-335, XP-432, XP-435

and many more, please ask if unsure .

60ml Kit

 

Includes: 1 x 60ml Solution,1 x Syringe, 1 x Tube, pair gloves, paper towel.

 

Background information.

The above epson printers have a permanent printhead, this allows Epson to use a very high quality printhead, and you may know that if you come to replace it can cost as much as the original printer.

If you use Original Epson ink or compatible, then at some point you WILL get blocked nozzles and no matter how many cleaning cycles you do nothing seems to improve.

At this point it is important to understand why.

Newer printers print in higher quality so the nozzles become smaller, newer printers are usually faster than their predecessors, and therefore the ink needs to dry faster.  This combination is why your nozzles can become blocked whether the printer is 1 month old or 24 months old.

When you replace your cartridge, you notice a problem with your print quality, so you peform a nozzle check, noticing there are a few missing lines you perform a nozzle clean cycle on your printer, this fires ink through all the nozzles and then physically wipes the head on an internal rubber strip.  Hey presto your printer is printing as it should again.  However sometimes head cleans can make the problem worse, the more cleans you do the more waste ink is smeared over the head, and all this ink has to go somewhere, owners who have had epsons over a number of years will know what a waste pad is, well this is where all that ink goes when you perform a cleaning cycle.  Performing one or two head cleans should be enough you should never perfom more than three sequencially, as not only will this empty your inks but it will fill your waste catcher over the service station with lots of waste ink and more than likely your yellow will become darkened as it sits over the waste ink in the printer.

Runing these cleans can deplete your ink cartridge, so you may need to replace them sooner than necessary costing you more money in cartridges, just because your cyan is blocked doesnt mean thats the only ink being used in the cleaning cycle, it uses all of the ink cartridges not matter whether they are ok or not.

Sometimes you may wait until your ink completely runs out rather than replacing it when it shows low, at this point there is no ink left in the nozzles and they will become filled with air, air will block the natural flow of the ink through all of the nozzles and it will take the path of least resistance which may cause it to miss a few lines in your printout, much clearer seen on a nozzle check pattern.  All is not lost though, when you insert a new cartridge, the printer will self charge, this is the printers way of trying to force through any air and any dried ink, however effective this might be there can be more stubborn nozzles that will stay blocked.

Things that may help your printers nozzles are.

  1. Never run more than three cleaning cycles, if it is not printing correctly after this you will need to manually clean the printheads.
  2. Try to print something once a week, this will keep the ink from drying out in the nozzles,
  3. Dont be afraid to turn your printer off and on again, when you printer is turned on it does a small cleaning cycle much less harsh than the one on the menus.
  4. Use good quality inks, whether these are genuine or compatible, the ink quality must be good as any large particles in the catridge will only get stuck in your head.

If your nozzles are blocked then our kit could help you, the instructions for it are listed below.

Everything is included in the kit for you to perform a manual clean of your printers head.

Instructions for use :

1.Run Nozzle check

2.Remove ink cartridges (& printhead if possible)

3.Inject 2ml PM solution into effected nozzle.

4.Leave for 5-10 mins

5.Change blotting/catcher paper.

6.Inject another 2ml PM solution.

7.Reinstall printhead if removed, and use fresh catridges.

8.Run Nozzle check

more hints and tips in the kit !!

We sell 30ml, 60ml, 120ml, 250ml 500ml Kits

this is the 60ml kit

 

Please take care using this solution, as damage to your printer can be done if spillage or splashes occur over moving parts or electronics, wipe dry immediately, and make sure the power is disconnected from your printer at all times. Wear gloves and goggles at all times.

 

 

WE TRY OUR BEST TO DESPATCH SAMEDAY IF ORDERED BEFORE 3PM MON-FRI

For small items we use Royal Mail 24 or 48 medium items we use Hermes (2-3 days), Large items or Express shipping UKMail (next day) or other courier (regardless of whats stated at checkout)

Please understand that all of the items we list on ebay are also on our website and on other e-commerce sites, occasionally the item you purchase may have already been purchased from another site, in which case we will try and source a replacement immediately or refund your money in full within 48hrs if a replacement cannot be found. 


PLEASE NOTE  NON of my Epson kits will fit the XP-500, 600 700 800 900 series This is because they do not have round nozzles for the pipes to fit on securely. If your printers nozzles are round then my kit should fit 95% of the time, if in doubt please ask.
Gloves can be blue, purple, clear, other depending on stock levels, we use nitrile and vinyl but not latex due to skin allergies.
The "Red" pipe in the picture may change due to stock levels, it maybe clear or another colour.
  • Condition: Neuf
  • MPN: PM-60ML-XP322
  • Unit Type: Unit
  • Media Type: Printer
  • Country/Region of Manufacture: United Kingdom
  • Unit Quantity: 1
  • Brand: Printhead Magic
  • Type: Cleaning Kit
  • EAN: 7103657073489

PicClick Insights - Epson Printer nozzle unblocker 60ml Printhead cleaner XP-322 XP-325 PicClick Exclusif

  •  Popularité - 8 personnes suivent la vente, 0.0 de nouvelles personnes suivent la vente par jour, 2.821 days for sale on eBay. Super grande quantité suivi. 278 vendu, 10 disponibles.
  •  Meilleur Prix -
  •  Vendeur - 9.159+ articles vendu. 0.3% évaluations négative. Grand vendeur avec la très bonne rétroaction positive et plus de 50 cotes.

Les Gens ont Aussi Aimé PicClick Exclusif