30623 Seal Kit for Cat Pump 30 31 34 35 310 340 350 Model Pressure Washer Repair

• This 30623 Repair Seal Kit perfectly fits for CAT Pump Pressure Washer Pump 30, 31, 34, 35, 310, 310B, 310S, 310W, 340, 340S, 340B, 340W, 350, 350S, 350B, 350W Models, 5 Frame Plunger Pumps. One kit is required per pump.

• Used to replace broken, damaged and worn seals and O-ring for CAT PUMP. Choose us and you can effectively solve the problems of water leakage, loss of pressure and performance degradation.

Usa-auto-plus

Your best choice

Perfect Fitment

• This 30623 Repair Seal Kit perfectly fits for CAT Pump Pressure Washer Pump 30, 31, 34, 35, 310, 310B, 310S, 310W, 340, 340S, 340B, 340W, 350, 350S, 350B, 350W Models, 5 Frame Plunger Pumps. One kit is required per pump.

Solve Water Leakage Problems

• Used to replace broken, damaged and worn seals and O-ring for CAT PUMP. Choose us and you can effectively solve the problems of water leakage, loss of pressure and performance degradation.

Superior Material

• Made of high quality NBR(Nitrile Rubber), all seals and O-rings features with good oil resistance, corrosion resistance & wear resistance. The Wick (Long Tab) made of oil absorbent cotton, ligh weight and durable. Long-lasting rubber o-ring, no breakage. Professional machines manufacturing ensures high quality of our products. The seal kit has been high temperature tested and can handle temperature up to 160°F.

What You Will Get

• Comes with 3PCS #43307 high-pressure seals with S seal; 3PCS #43305 low-pressure seals with S-Spg seal; 3PCS #14200 seal case o-rings; 3PCS #17399 plunger retainer o-rings; 3PCS #43302 long tab wicks.

100% Satisfaction Guarantee

• The johntruck Team aims to provide you the best products and services. Support 30 days returns and 12 months warranty. Please feel free to contact us if you have any question.

Specific Installation Steps

• Step 1: Remove the maniford: Use a 8mm wrench to remove the 2 hex socket head screws. Seperate the maniford and crankcase: Use 2 flat tip screwdrivers to pry maniford away from the crankcase. Use a rubber hammer to completely remove maniford from crankcase place.

• Step 2:  Remove the low-pressure seals, seal case o-ring and high-pressure seals: Put the maniford on flat surface with low pressure seals facing up. Place a flat tip screwdriver under the low pressure seal and pry upward to remove. Be careful not scratch the inner diameter surface of the steel case where the low pressure seals are located. Inspect the inside of the low pressure seal for wear or damage. Using a half inch seam case tool or tee wrench remove the seal case. Inspect the seal case o-rings for cut nick's or damaged. Use a flat tip screwdriver under the high pressure seals and pry upward to remove.

• Step 3:  Install the low-pressure seals, seal case o-ring and high-pressure seals: Before installing , apply a liquid gasket to outside surface of the high pressure seals. With the flat side facing up, put the high pressure seals into place. Replace a new o-ring on the seal case, apply liquid gasket to the o-ring on the seal case. Install the seal case with the o-ring down into the mainford and thread into maniford. Using your seal case tool or tee wrench to tighten. With the spring side facing down, put the low pressure seals into place.

• Step 4:  Replace the wicks and small o-rings: Remove the nylon oil pan. Remove the two-piece seal retainer with wick. Put apart the retainer by hand, replace the wicks. Ensure the hole in the retainer is facing down when reinstalling. Use a 12 mm wrench lossen and remove the plunger retainer, replace the small o-ring on it. Apply thread sealant on the end of the plunger rod. Install plunger assembly and tighten using a 10 mm wrench torque to specification. With the hole and long tail of the wick facing down, install the plunger retainer. Put the oil pan back in place.

• Step 5:  Adjust to specification: Before reinstalling the maniford, rotate the crankshaft so that the outside two plungers are even up for this distance from the crankcase. Install the maniford by hand, ensure even alignment. Use a rubber hammer to ensure maniford is flush to crankcase surface. Reinstall the two hex socket head screws. Use a 8mm wrench to tighten and torque to specification.

1. Payment methods accepted: Paypal only . Our Paypal account allows you to pay by credit card, debit card and your Paypal balance.

2. All major credit cards are accepted through our secure payment processor Paypal.

3. Payment must be received immediately.

4. We ship items to Your Paypal address .Please make sure your Paypal address is correct before you pay,cause it cannot be changed once the order shipped out.

1. Item will be shipped within 1 business day after your payment cleared.

2. Item will be shipped by SpeedPak or other shipping method .

3. Delivery time depends on destination and other factors,please feel free to contact us by email if you cannot get your order in time.
 

Please read the shipment and payment detail carefully before you place the order .

1. Return to us within 60 days from the delivery date for exchange or refund. Refund will be given as Money back or item exchange (buyer's choice).

2. Return shipping fee is the responsibility of buyer unless the return is a result of our mistake.

3. If you need return, please contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation.

Please contact us via ebay using"Contact member". We will respond within 1 business day or less.Thank you for your understanding.

Our office hours is as below :
 

Usa-auto-plus

Your best choice

• Condition: Neuf
• Type: Seal Kit
• Number in Pack: 15
• Marque: UAP-Auto
• Numéro de pièce fabricant: 30623